Shop guide: drawer boxes

How do I size a wood drawer box for undermount slides?

Start from the cabinet opening and the exact slide you're using, because the slide maker sets the box width, height and length. Take the opening width and height, pick the longest slide that fits the cabinet depth, then work out the box from that slide's clearances. Size the sides, front, back and bottom for your joint and bottom groove, and set your jig from its manual.

Undermount slides are fussy. A box that's 1/16 too wide binds, and every maker publishes its own clearances. Get the numbers from the slide, not from memory.

Drawer calculator: a 15 3/8 by 6 1/2 opening on a Blum TANDEM 563H slide gives a 14 3/4 W x 5 5/8 H x 21 L box, with sides, front and back and bottom sized, and the Porter-Cable jig setup
Real screen, sample shop
How to do it

From the opening to a box that slides right.

  1. Measure the opening, not the box.

    Face-frame opening width and height, and the inside depth of the cabinet. Fractions are fine.

  2. Pick the slide before the box.

    Brand, model and length decide the box. Use the longest slide that fits the depth.

  3. Use the maker's clearances.

    Each undermount slide has its own width, height and length rules. They're printed in the maker's spec sheet.

  4. Pick your side thickness to match the slide.

    Many undermount slides are made for 1/2 or 5/8 sides. Thicker sides need a slide made for them.

  5. Choose the joint.

    Half-blind or through dovetails, box joints, or butt joints with the front and back between or over the sides. The joint changes the front and back length.

  6. Groove the bottom.

    Decide your bottom thickness and groove depth. These are your shop's numbers, not the slide maker's.

  7. Set the jig from its manual.

    Template, bit depth and box height steps all come from the jig, so a box height that suits the jig saves a setup.

Where Square Away fits

The Drawer calculator.

Open Tools, Calculators, the Cut list tab, and tap Drawer calculator. Type the opening width, opening height, cabinet inside depth and how many. Pick the slide, your side thickness, bottom, groove depth and joint, and it gives you the box and every part.

  • Blum and Salice undermount slides, in the maker's own numbers. Blum TANDEM plus BLUMOTION 563H and 563F, TANDEM 569H heavy duty and MOVENTO 763H. Salice Futura A7555 / A7557, Futura A7955, and Progressa+ G7U6 and G7U9.
  • Length picks itself. It defaults to the longest slide that fits your cabinet depth, and marks the ones that need a deeper box.
  • Half-blind, through, box or butt joints. Butt joints ask whether the front and back go between or over the sides.
  • Porter-Cable jig setups. For dovetails and box joints on a Porter-Cable 4210, 4212 or 4216 jig, it gives the setup steps with the manual page for each. Where the manual prints no number, it says to set it from the manual instead of guessing.
  • Snap to the jig's height. Tick it and the box height drops to the jig's even height, and it tells you what it changed.
  • The answer: the box size, a parts table for sides, front and back and bottom, the bottom groove, what the slide needs, and how it was worked out with the sources. Print it or copy it.
Ask it on the phone

Or just ask Shop Hand.

On the Shop plan and up, ask Shop Hand something like "size a drawer for a 15 3/8 by 6 opening" and it works the same math in the chat.

Straight talk

What it does, and what it leaves to you.

Wood boxes on undermount slides only.

Metal-sided drawer systems aren't in it. This is for the wood drawer boxes you build.

Porter-Cable is the jig with real settings.

Pick Other jig and you get the joint math without jig numbers. Tell us your jig and we'll look at adding it.

It doesn't save or send the parts.

Print or copy the list. It doesn't go to the cut planner or the estimate on its own.

Your bottom, your groove.

Neither maker prints a bottom thickness or groove depth, so those stay your numbers.

Questions shop owners ask

More on drawer boxes.

Is the drawer calculator free?

Yes. It's under Tools, Calculators on every Square Away plan, with no job needed.

Which drawer slides does it support?

Blum TANDEM plus BLUMOTION 563H and 563F, TANDEM 569H and MOVENTO 763H, and Salice Futura A7555/A7557, A7955 and Progressa+ G7U6 and G7U9, all undermount slides for wood boxes.

Can I use 3/4 drawer sides with undermount slides?

Only with a slide made for them. With 3/4 sides the calculator offers the slides rated for it, and shows the rabbeted-side shop method separately, marked as not the maker's spec.

Does it give dovetail jig settings?

For the Porter-Cable 4210, 4212 and 4216 jigs, yes, step by step with the manual page for each. Other jigs get the joint math only.

Size your next drawer run on the call.

Bring a cabinet you're quoting. We'll run the drawer boxes and the door list together and put the parts on the job.

Book a free setup callClaim your Founding Shop spot